3D Printed Viking Runes - Castlemaker
$24.99
Castlemaker has created a full set of 24 runes that you can use to cast your fortunes - or as a prop at your gaming table.
Each Rune is about 24.20mm x 16.45mm x 7.92mm.
This 3d printed object has been made to order, it is supplied unpainted, and please allow time for manufacturing. The image shown is a 3D render.
I try to ensure all supports were removed; however, there may be some minor clean up required. Clean up can be achieved with a sharp blade scraped gently over the affected areas, or with fine sandpaper. If sanding or causing resin dust, please take care not to breathe it in. Further if the model is slightly sticky or tacky, make sure to leave it in direct sunlight until fully solid, making sure to wash your hands afterwards with soap as uncured resin can irritate the skin.
This storefront is fully licensed to print and sell the shown miniature from Castlemaker.
Each Rune is about 24.20mm x 16.45mm x 7.92mm.
This 3d printed object has been made to order, it is supplied unpainted, and please allow time for manufacturing. The image shown is a 3D render.
I try to ensure all supports were removed; however, there may be some minor clean up required. Clean up can be achieved with a sharp blade scraped gently over the affected areas, or with fine sandpaper. If sanding or causing resin dust, please take care not to breathe it in. Further if the model is slightly sticky or tacky, make sure to leave it in direct sunlight until fully solid, making sure to wash your hands afterwards with soap as uncured resin can irritate the skin.
This storefront is fully licensed to print and sell the shown miniature from Castlemaker.
Quantity:
Castlemaker has created a full set of 24 runes that you can use to cast your fortunes - or as a prop at your gaming table.
Each Rune is about 24.20mm x 16.45mm x 7.92mm.
This 3d printed object has been made to order, it is supplied unpainted, and please allow time for manufacturing. The image shown is a 3D render.
I try to ensure all supports were removed; however, there may be some minor clean up required. Clean up can be achieved with a sharp blade scraped gently over the affected areas, or with fine sandpaper. If sanding or causing resin dust, please take care not to breathe it in. Further if the model is slightly sticky or tacky, make sure to leave it in direct sunlight until fully solid, making sure to wash your hands afterwards with soap as uncured resin can irritate the skin.
This storefront is fully licensed to print and sell the shown miniature from Castlemaker.
Each Rune is about 24.20mm x 16.45mm x 7.92mm.
This 3d printed object has been made to order, it is supplied unpainted, and please allow time for manufacturing. The image shown is a 3D render.
I try to ensure all supports were removed; however, there may be some minor clean up required. Clean up can be achieved with a sharp blade scraped gently over the affected areas, or with fine sandpaper. If sanding or causing resin dust, please take care not to breathe it in. Further if the model is slightly sticky or tacky, make sure to leave it in direct sunlight until fully solid, making sure to wash your hands afterwards with soap as uncured resin can irritate the skin.
This storefront is fully licensed to print and sell the shown miniature from Castlemaker.
Castlemaker has created a full set of 24 runes that you can use to cast your fortunes - or as a prop at your gaming table.
Each Rune is about 24.20mm x 16.45mm x 7.92mm.
This 3d printed object has been made to order, it is supplied unpainted, and please allow time for manufacturing. The image shown is a 3D render.
I try to ensure all supports were removed; however, there may be some minor clean up required. Clean up can be achieved with a sharp blade scraped gently over the affected areas, or with fine sandpaper. If sanding or causing resin dust, please take care not to breathe it in. Further if the model is slightly sticky or tacky, make sure to leave it in direct sunlight until fully solid, making sure to wash your hands afterwards with soap as uncured resin can irritate the skin.
This storefront is fully licensed to print and sell the shown miniature from Castlemaker.
Each Rune is about 24.20mm x 16.45mm x 7.92mm.
This 3d printed object has been made to order, it is supplied unpainted, and please allow time for manufacturing. The image shown is a 3D render.
I try to ensure all supports were removed; however, there may be some minor clean up required. Clean up can be achieved with a sharp blade scraped gently over the affected areas, or with fine sandpaper. If sanding or causing resin dust, please take care not to breathe it in. Further if the model is slightly sticky or tacky, make sure to leave it in direct sunlight until fully solid, making sure to wash your hands afterwards with soap as uncured resin can irritate the skin.
This storefront is fully licensed to print and sell the shown miniature from Castlemaker.